AS ONE Corporation

• Model number: HP-1SA
• Highest temperature: 430?
• Plate size: 180 x 180mm
• Plate material: Aluminum die cast (ceramic coating)
• Main unit size: 200 x 260 x 118mm
• Operating temperature range: Room temperature +10 - 430?
• Temperature control system/sensor: Microcomputer type PID control/K thermocouple sensor
• Timer function: Setting range/1 minute - 99 hours 59 minutes (1 minute unit)
• Heater capacity: 1300W
• Power supply: 100VAC 50/60Hz
• Temperature distribution width: -4?
• Highly accurate temperature can control at 4? in temperature distribution width(set as 200?).
• It is with prevention display function from burn injury.

• Model number: HP-2SA
• Highest temperature: 430?
• Plate size: 180 x 180mm
• Plate material: Aluminum die cast (ceramic coating)
• Main unit size: 200 x 260 x 118mm
• Operating temperature range: Room temperature +10 - 430?
• Temperature control system/sensor: Microcomputer type PID control/K thermocouple sensor
• Timer function: Setting range/1 minute - 99 hours 59 minutes (1 minute unit)
• Program function: 1 pattern 8 steps/temperature and time settings for each step
• Heater capacity: 1300W
• Power supply: 100VAC 50/60Hz
• Temperature distribution width: -4?

• Model number: GTB-60
• Material: Cover/PC (polycarbonate), Wire fastener/PA (nylon 66)
• Recommended gas flow: To 3L/min (MAX)
• Valve: IN/PISCO BVLC20-0602, OUT/BVVC20-0802 (OUT)
• Positive pressure safety valve: Minimum operating pressure 98.1Pa (10mmAq)
• Size: 450 x 400 x 345mm
• *You cannot use it in an atmosphere of 80? or more. *Make sure you place decompression equipment in front of gas inlet, Do not apply gas pressure of more than 294Pa (30mmAg). *You cannot use it in decompression environment.
• Such as nitrogen atmosphere etc. can be made the environment of hot plate in simple.

• Model number: GTB-105
• Material: Cover/PC (polycarbonate), Wire fastener/PA (nylon 66)
• Recommended gas flow: To 3L/min (MAX)
• Valve: IN/PISCO BVLC20-0602, OUT/BVVC20-0802 (OUT)
• Positive pressure safety valve: Minimum operating pressure 98.1Pa (10mmAq)
• Size: 600 x 500 x 395mm
• *You cannot use it in an atmosphere of 80? or more. *Make sure you place decompression equipment in front of gas inlet, Do not apply gas pressure of more than 294Pa (30mmAg). *You cannot use it in decompression environment.
• Such as nitrogen atmosphere etc. can be made the environment of hot plate in simple.

• Model number: ACFAFA 20 W
• Type: W / wide-mouth type
• Capacity (mL): 20
• Body diameter x height (mm): f 28 x 61
• Diameter (f mm): 16
• Material: High purity PFA
• No scale
• Structure of cap prevents leakage even though internal cap is not used.
• This bottle has been acid-washed to remove trace metal ion contaminants, particles, and grease inside container.

• Model number: ACPFA100-W
• Type: W, wide-mouth type
• Capacity (mL): 100
• Body diameter x height (mm): f45 x 104
• Mouth diameter (fmm): 26
• Material: High-purity PFA
• With scale
• Structure of cap prevents leakage even though internal cap is not used.
• This bottle has been acid-washed to remove trace metal ion contaminants, particles, and grease inside container.

• Model number: ACPFA-250-W
• Type: W, wide-mouth type
• Capacity (mL): 250
• Body diameter x height (mm): f60 x 153
• Mouth diameter (fmm): 34
• Material: High-purity PFA
• With scale
• Structure of cap prevents leakage even though internal cap is not used.
• This bottle has been acid-washed to remove trace metal ion contaminants, particles, and grease inside container.

• Model number: ACPFA-500-W
• Type: W, wide-mouth type
• Capacity (mL): 500
• Body diameter x height (mm): f73 x 170
• Mouth diameter (fmm): 45
• Material: High-purity PFA
• With scale
• Structure of cap prevents leakage even though internal cap is not used.
• This bottle has been acid-washed to remove trace metal ion contaminants, particles, and grease inside container.

• Model number: ACPFA-1000-W
• Type: W, wide-mouth type
• Capacity (mL): 1000
• Body diameter x height (mm): f94 x 200
• Mouth diameter (fmm): 45
• Material: High-purity PFA
• With scale
• Structure of cap prevents leakage even though internal cap is not used.
• This bottle has been acid-washed to remove trace metal ion contaminants, particles, and grease inside container.

• Model number: EAP-01
• Body (with AC adapter)
• Maximum discharge flow rate: 1.5L/min
• Maximum pressure: 26.6kPa (200mmHg)
• Maximum vacuum attainment level: -26.6kPa
• Connection port size: f5.5mm nipple
• Gas contact unit material: Chloroprene, PB Resin
• Power supply: DC12V AC100V 53W (AC adapter included)
• Power cord length: Approx 1.5m
• Weight: 235g
• For both discharge and suction
• Size: 57 x 166 x 36mm
• It is mini air pump which can be used also in laboratory or the field.
• If an optional battery pack is used, also outdoors, it can be used.
• It can be used also as small compressor.
• It is possible to change the amount of air intakes in volume.

• Model number: EAP-11
• Battery pack
• Power supply: AA battery x 8 pieces (included for test)
• Power cord length: Approximately 1.7m (2P plug)
• Weight: 305g (including cell)
• Size: 72 x 65 x 38mm

• Model number: TP-1973D
• Applicable tube type: Soft tube such as Tygon (R), Silicone, Viton (R)
• Power supply: 100VAC 50/60Hz
• Power cord length: 1.6m (2P plug)
• Main unit size: 145 x 68 x 115mm
• Weight: 620g
• Accessories: AC adapter
• Discharge quantity: 5 - 90mL/min
• Applicable tube inner diameter outer diameter: f3.18 x 6.35mm
• These products are self-priming pumps, and do not require priming water.
• Possible to open the front cover, and replace tube very easily.
• These products can transfer liquid of high viscosity such as slurry.
• LED indicator indicates the load(torque) applied on the motor(in the TP-1973D and TP-1973R).
• The microcomputer controls rotation, and offers stable pumping operation even at low speed(in the TP-1973D and TP-1973R).

• Model number: TP-1973
• Applicable tube type: Soft tube such as Tygon (R), Silicone, Viton (R)
• Power supply: 100VAC 50/60Hz
• Power cord length: 1.6m (2P plug)
• Main unit size: 145 x 68 x 115mm
• Weight: 620g
• Accessories: AC adapter
• Discharge quantity: 62 - 90mL/min
• Applicable tube inner diameter outer diameter: f3.18 x 6.35mm
• These products are self-priming pumps, and do not require priming water.
• Possible to open the front cover, and replace tube very easily.
• These products can transfer liquid of high viscosity such as slurry.
• LED indicator indicates the load(torque) applied on the motor(in the TP-1973D and TP-1973R).
• The microcomputer controls rotation, and offers stable pumping operation even at low speed(in the TP-1973D and TP-1973R).

• Model number: TP-1973R
• Applicable tube type: Soft tube such as Tygon (R), Silicone, Viton (R)
• Power supply: 100VAC 50/60Hz
• Power cord length: 1.6m (2P plug)
• Main unit size: 145 x 68 x 115mm
• Weight: 620g
• Accessories: AC adapter, PharMed (R) tube 200mm
• Discharge quantity: 0.8 - 5mL/min
• Applicable tube inner diameter outer diameter: 2.38 x 5.56mm
• These products are self-priming pumps, and do not require priming water.
• Possible to open the front cover, and replace tube very easily.
• These products can transfer liquid of high viscosity such as slurry.
• LED indicator indicates the load(torque) applied on the motor(in the TP-1973D and TP-1973R).
• The microcomputer controls rotation, and offers stable pumping operation even at low speed(in the TP-1973D and TP-1973R).

• Model number: RTS-1973
• Capacity: 19L
• Body material: PC (polycarbonate)
• Maximum outer diameter: 367fmm
• Inner diameter: f306mm
• Overall height: 498mm (including vacuum gauge)
• Metal cock outer diameter: Side of body/f9mm, Vacuum gauge/f8mm
• Weight: Approx 3kg
• Simple and compact design.
• By reducing pressure in water, can be checked leak status in containers.
• Body is sturdy by PC(polycarbonate) made.
• Can hold vacuum status without using grease.

• Model number: TXN-25A
• Temperature settings range (Pt sensor/K class thermocouple): 0.0 - 200.0?/0 - 500?.
• Temperature control system: PID control, SSR output
• Connection capacity: AC100/200V 25A
• Timer type: Autostart, auto-stop, SV start
• Timer setting available time: 1 minute - 99 hours 59 minutes
• Temperature indication accuracy: +/- 2? or +/- 0.3% + 1 digit, whichever is larger
• Output: Control voltage output/AC100/200V 25A, Alarm contact output/AC100/200V 2.4A
• Power cord: Non (connected to power terminal on the back terminal block)
• Safety device: Overcurrent breaker
• Size: 190 x 239 x 220mm
• *Sensor is not included in the package. Please select one of the shape, type according to the application (no connector type).
• *Power cord is not included. Please prepare according to used power voltage.
• Since it is mass thermoregulator of max. 25A, control of large-sized heater etc. is possible.
• Since it is 100V, 200V combination, possible to use it broadly in one set.
• Timer set of 3 patterns is possible.
• Both K type thermo couple and Pt100ohm can be used(factory setting is K type thermo couple).

• Model number: I-COVER
• Temperature adjustment range: Room temperature + 5 - 45? (warm air blow temperature)
• Forced convection system
• Heater: 200W
• Temperature adjustment system: Thermostat type, dial type
• Material: Body/transparent PMMA (Acrylic) thickness 4mm, Heater unit/steel plate baking coating
• Power supply: 100VAC 50/60Hz
• Inner chamber dimension: 422 x 372 x 346mm
• External dimensions: 450 x 400 x 440mm
• Weight: 9kg
• With stick thermometer for checking chamber temperature
• *Temperature control range may vary if you put the heater in the chamber. *Temperature scale of the temperature control dial is the standard.
• Use by just covering a sample.
• Four directions are acrylics windows, the status of sample can be checked easily.

• Model number: HGS-01
• Size: Height 850 - 1120mm
• Material: Body/Stainless Steel (SUS304), Leg section, handle section/steel
• Weight: Approx 17kg
• Stroke: 31mm
• Water tank middle cylinder (stainless steel (SUS304))): f235mm
• Outer diameter of drainage receiver connection port : f15 - 25mm taper
• Chamber dimensions: f235 x 280mm
• It is manual compression machine for small-quantity samples in experiment level.
• It is the structure which moisture flows into the tub lower part by using the pipe in tank, and is summarized to one place with drainage receptacle.
• Since the hole is open to the tub, liquid is extractable from the lower part.
• Other portions are easy to decompose including handle portion.

• Model number: MR-1
• Specification: Drive part
• Conform syringe: 10?L - 5mL
• Size (mm): 171 x 45 x 83
• Motor: Small stepping motor
• Syringe number of hanging: 1 piece
• Weight: 0.7kg
• Applicable syringe capacity: 10?L - 5mL
• *Syringe is not included in the package.
• *Please use a set of controller unit and drive unit.
• *Capacity scale is set for 60mm syringe with the speed scale, So you need to do scale conversion with other syringes.
• Place only drive unit in chamber or similar part to remotely control from outside of pump.
• Flow rate can be easily adjusted simply by turning dial to desired graduation.
• Add remote control cable(sold separately) to operate 2 drive units at the same time.
• MR-1 can be secured to stand.

• Model number: TVC-01N
• Specification: Bio trap set
• Size (mm): -
• Material: Flask/PP (Polypropylene), Hose/Silicone rubber (4m in length)
• Flask capacity: 1L
• Flask diameter x height: f30 x 220mm
• Intake port/f8mm
• Tip + Pipet connecting portion Diameter: f7.5mm
• 8 Channel Disposable Pipette Material/Low Density PE (Polyethylene), Size/65 x 130mm, Nonautoclavable
• Set content: Hose (f6 x f9mm), Trap (1000mL), Adapter, Red Rubber plug (with Hose Joint)
• *Pump, Tip, 8 channel Disposable pipette, Foot switch are not included in the package.
• Facilitates the collection of liquid when attached to a small pump.
• The provided filtration bottle made of PP(polypropylene)eliminates concerns about breakage.